기본 정보
Dimension(mm)
200 X90 X50
제품 설명
1.Product Introduction
Optical Multi Meter is a handheld and intelligent instrument, which can be used as optical power meter and stabilized light source, and can constitute integral test system. It is an updated version of a popular in the industry optical power meter Handheld Power Meter with a built in LD stabilized light source at 1310,1550nm wavelength, one port output .It is specifically designed for technical support personnel to take a variety of instruments with a single meter.
2. Specifications
Type | ALK1231 |
Optical Power Meter Module |
Detector Type | InGaAs |
Measurement Range(dBm) | -70~+6 | -50~+26 |
Uncertainty | 5% |
Calibrated wavelengths(nm) | 850,1300,1310,1490,1550,1625 |
Resolution(dB) | 0.01 |
Optical Connector | FC(interchangeable SC,ST) |
Optical Light Source Module |
Emitter Type | FP-LD |
Wavelengths | 1310/1550(other wavelengths can be optional) |
Ouput Power(dBm) | -7 |
Spectral Width | ≤10nm |
Output Stability | ±0.05dB/15mins; ±0.1dB/ 8hours |
Optical Connector | FC/ PC |
General Specifications of Multi Meter |
Power Supply | Alkaline Battery(3 AA 1.5V batteries) |
Battery Operating Time | ≥60 hours(Both Power Meter and Ligh Source are working) ≥240hours(Only Power Meter is working) |
Auto-off time | 10mins |
Operating Temperature(ºC) | -10~+60 |
Storage Temperature(ºC) | -25~+70 |
Dimension(mm) | 200 X90 X50 |
Weight (g) | 285 |
3. Standard Packages
Handheld Optical Multi Meter...............1
Manual............................1
AA Battery ............................1
Carrying Case........................1
Cotton Swabs................................1
4.Optical fiber loss measurement
Step 1- Optical Reference Level
Turn on optical power meter and press the λ key to select the wavelength.
Turn on optical light source (emitting source) and select the wavelength. Wait for 1-2 minutes until it stabilize.
Select a piece of patch cords, which is used to connect with the light source, we call it emitting patch cords. Cleaning connector of the patch cords. The fiber of the emitting source patch cords must be the same fiber type as the fiber under test.
Connect the light source (emitting source) with the Handheld Power Meter through the emitting source patch cords
Handheld Power Meter get the power measurement value.
This value should be close to the one that light source (emitting source) set. If it has wide disparity, please make sure the fiber connection is clean properly else replace another jumpers.
Step 2-Optical Loss Measurement
Keep the emitting source patch cords connection with the light source (emitting source).
Connect the Handheld Power Meter and light source (emitting source) to the optical fiber link respectively.
Notes: cleaning all the connectors surface including all the necessary optical adaptors. The reading in dB unit displayed on the screen is the tested optical fiber link loss.(also display the current absolute optical power value in dBm unit).
5.Maintenance
1.It is important to keep all optical connectors and surfaces free from oil, dirt or other contamination to ensure proper operation.
2.Keep using one type of adapter to avoid excess loss from different connectors.
3.Please use dust proof cap for protection to avoid begin scratched or contaminated when Handheld Power Meter not in operation.
4.Light interface is sensitive, please carefully plug in and pull out the connectors.
5.Please use clean cotton to clean the sensor surface, clean it in clockwise direction carefully.
6.If does not need to use for a long time, please take out the battery.
6.Troubleshooting
Description | Problem | Method |
Faint LCD display \No display after turning on the unit | Battery is weak/Others | Turn on the unit again/Change battery |
Insensitive display in LCD | Light interface is polluted/ broken/Display locked | Check connector carefully and clean sensor's interface |
8.Change Battery
8.1If you find battery is weak while operating it, please immediately turn the unit off and change a new battery.
주소:
16th Floor, Creativity Center, Jinnan District, Tianjin300352, China
사업 유형:
제조사/공장
사업 범위:
가전제품, 서비스, 전기전자, 측정 기계
경영시스템 인증:
ISO 9001, ISO 14001
회사소개:
Tianjin Eloik Communication Equipment Technology Co., Ltd는 독일 기술을 보유한 CE 인증 회사로 중국 내 광 통신 장비의 연구, 개발, 생산 및 판매를 전문으로 합니다. 주요 제품은 광 섬유 융합 플리커, OTDR, 광전원 측정기, 광광원, VFL 등입니다.
이 회사는 오랜 세월 동안 광전자 통합 개발 경험을 쌓은 독일 전문가로 구성된 강력한 R&D 팀을 보유하고 있습니다. 또한 엄격한 고급 생산 관리 기술과 ISO9001 품질 보증 시스템을 갖추고 있으며 완벽한 판매 후 추적 서비스 시스템을 제공합니다. 우리는 항상 "제품"의 개선을 유지하고, "서비스"를 통해 고객 편의를 위한 관리 개념을 만들고, 우리 팀의 모든 힘을 가지고 국내외의 광학 통신 분야에 더 나은 제품을 만듭니다.
Tianjin Eloik Communications Equipment Technology Co., Ltd는 중국 통신업체 3개사인 China Unicom, China Telecom 및 China Mobiles의 공급업체 목록에 있습니다.
엘릭은 사용자에게 더 나은 제품과 더 만족스러운 서비스를 제공하기 위해 항상 노력할 것입니다.
CE 인증서와 ISO 인증서를 획득했으며, Fusion 접속 구성 회사의 스페인, 영국, 미국, 호주, 인도네시아, 인도, 러시아 등