기본 정보
High Temperature
-20oc~+180oc
Low Temperature
-20oc~+90oc
Bleed Pressure
0.3MPa~0.7MPa(Largest:1.0MPa)
제품 설명
|
AW series pneumatic actuators are divided into double action and single action type (spring reset), two divided cylinder, large output torque, flexible operation balance; piston rod hard chromium plating, good wear resistance; all sliding parts between with or without oil lubrication oil and the guide ring to reduce the friction coefficient, prolong the service life, aw and gas dynamic execution of U-shaped curve output torque is more suitable for large-diameter ball valve, butterfly valve angle stroke of the valve opening and closing adjustment, is used in cases of other rotary motion, is to achieve an ideal device for industrial pipeline automation control. |
technical parameter | |
Bleed pressure | 0.3MPA~0.7MPA(largest:1.0MPA) |
ambient temperature | basic:-20ºC~+90ºC |
high temperature:-20ºC~+180ºC |
low temperature:-20ºC~+90ºC |
Turning angle | 90ºC±5° |
Air excuse | AW13-G1/4 |
AW17-G3/8 |
AW20~AW40-G1/2 |
Model establishment Pneumatic actuator --------------------AW Pneumatic inner diameter size 12/17/20/28/35/40---------28 Single acting (spring reset) -----------S S hand operating mechanism -------------S |
Model selection |
?Selection of AW pneumatic actuator, first determine the valve opening and closing torque, and then according to the valve used in the fluid medium, increase the safety value. On the clean, the lubrication medium increases 20% security value; the water vapor or the non lubricating medium increases 25% security value; Fei Runhua's dry gas medium increases 60% security value; the non lubricated gas transportation of particles powder material medium increases 100% security value. And then according to the source of gas pressure, to find a double acting or single acting type of output torque meter, can get accurate actuator model. Single acting type of output torque meter, the minimum spring torque that is to close the valve when the torque, the maximum spring torque is to open the valve when the torque. |
Function and application of pneumatic actuator accessories |
1 double acting actuators: two bit control for valve opening and closing. |
2 single acting actuator (spring reset): in the circuit, gas circuit cut off or when there is a failure, automatic closing valve. |
3 single solenoid valve: when the valve is opened or closed, the valve is closed or opened when the power is off, the valve is closed or opened (can provide explosion-proof type). |
4 double solenoid valve: the valve is opened when a coil is energized, the other coil is energized when the valve is closed. |
5 limit switch back to the hearing device: long-distance transmission of the valve switch signal (which can provide explosion-proof type). |
6 electrical locator: according to the current signal (4-20mA) the size of the valve to the medium flow control (can provide explosion-proof type). |
7 electrical converter: the current signal is converted into an air pressure signal, and pneumatic positioner supporting the use of (can provide explosion-proof). |
8 pneumatic positioner: according to the current signal (standard 0.02-0.1MPA) the size of the valve of the medium flow control. |
9 air source treatment: including air pressure reducing valve, filter, oil mist. On gas source stability, cleaning and moving parts gas lubrication. |
10 hand operating mechanism: automatic control in the case of the valve can be operated manually open and close the valve. |
Main dimensions and connection dimensions Q644(5)(N,P,H,Y)-PN16(1.6MPA) |
| L | ml | H | ΦC | ΦD | f | Φd | I | Φf | P | b | t |
LDAW13 | 640 | 201 | 266 | 100 | 132 | 4-M16 | 42 | 37 | 80 | 4 | 12 | 3.5 |
LDAW17 | 827 | 270 | 348 | 160 | 190 | 8-M16 | 50 | 60 | 120 | 4 | 14 | 3.5 |
LDAW20 | 1162 | 350 | 425 | 200 | 232 | 8-M16 | 64 | 74 | 140 | 4 | 18 | 4 |
LDAW28 | 1380 | 460 | 527 | 280 | 318 | 8-M20 | 85 | 100 | 220 | 4 | 25 | 5 |
LDAW35 | 1860 | 545 | 640 | 300 | 300 | 8-M24 | 105 | 100 | 300 | 10 | 28*2 | 6.4 |
LDAW40 | 1860 | 545 | 640 | 300 | 300 | 8-M24 | 105 | 100 | 300 | 10 | 28*2 | 6.4 |
Main dimensions and connection dimensions Q644(5)(N,P,H,Y)-PN16(1.6MPA) |
| L | L1 | ml | H | ΦC | Φd | I | Φf | P | b | t | J | G |
LDAW13S | 858 | 538 | 201 | 266 | 100 | 42 | 37 | 80 | 4 | 12 | 3.5 | 35 | 1/4 |
LDAW17S | 1090 | 675 | 270 | 348 | 160 | 50 | 60 | 120 | 4 | 14 | 3.5 | 66 | 3/8 |
LDAW20S | 1430 | 850 | 350 | 425 | 200 | 64 | 74 | 140 | 4 | 18 | 4 | 78 | 1/2 |
LDAW28S | 1845 | 1155 | 460 | 527 | 280 | 85 | 100 | 220 | 4 | 25 | 5 | 84 | 1/2 |
LDAW35S | 2605 | 1670 | 545 | 640 | 300 | 105 | 100 | 300 | 10 | 28*2 | 6.4 | - | 1/2 |
Double acting output torque |
? | bleed pressure MPA |
Model | 0.3 | 0.4 | 0.5 | 0.6 | 0.7 |
LDAW13 | 515 | 620 | 770 | 930 | 1080 |
LDAW17 | 950 | 1270 | 1590 | 1910 | 2230 |
LDAW20 | 215 | 2870 | 3580 | 4300 | 5020 |
LDAW28 | 5150 | 6860 | 8580 | 10300 | 12020 |
LDAW35 | 10120 | 13500 | 16870 | 20250 | 23620 |
LDAW40 | 13220 | 17630 | 22040 | 26450 | 30860 |
bleed pressure |
? | Spring torque | 0.4 | 0.5 | 0.6 |
model | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum |
LDAW13S | 240 | 450 | 170 | 380 | 320 | 530 | 480 | 690 |
LDAW17S | 580 | 1230 | 240 | 690 | 360 | 1010 | 680 | 1330 |
LDAW20S | 1250 | 2440 | 430 | 1620 | 1140 | 2330 | 1860 | 3050 |
LDAW28S | 3290 | 6050 | 810 | 3570 | 2530 | 5290 | 4250 | 7010 |
LDAW35S | 5860 | 10480 | 3020 | 7640 | 6390 | 11010 | 9770 | 14390 |
LDAW40S | 7540 | 15080 | 2550 | 10090 | 6960 | 14500 | 11370 | 18910 |
Calculation of cylinder capacity, weight and air consumption |
model | AW13 | AW17 | AW20 | AW28 | AW35 | AW40 |
cylinder capacity L | Double acting type A+B | 6.3 | 14.3 | 30.8 | 73 | 148 | 193 |
single-action B | 3.25 | 7.15 | 15.4 | 36.5 | 74 | 96.5 |
weight | Double acting type | 46 | 79 | 168 | 320 | 600 | 780 |
single-action | 62 | 112 | 219 | 445 | 835 | 1050 |
Notes |
Note: the double effect formula V= (A+B) |? (P+101.2), 98| ?M |
Single acting formula V=A| (P+101.2), 98| ?M |
V: NL/min (N L / min) |
P: KpaG (air pressure gauge) |
M: piston per minute |
A, B: cylinder capacity (see table) |
Convert Mpa to Kp by 1000 |
Installation and maintenance
1 pneumatic actuators can be directly connected with the valve, but also through the bracket and the valve installed on the streets and connected. Connecting fasteners shall not be loosened.
2 ensure that the actuator output shaft and the valve stem of the coaxial degree, and the rotation is flexible, there is no crawling phenomenon.
3 connecting pipes, fittings, accessories, etc. should be clean and clean.
4 solenoid valve outlet is always downward, when up or level, should be connected to elbow, so that the exhaust port down.
5 the air duct should be determined before commissioning, air pressure, voltage, signal and so on.
6 compressed air should be filtered, dry dew point -15 C the following to the desiccant.
7 adjust the solenoid valve should be open to the automatic position.
8 pneumatic operation, should be disconnected from the manual device, manual operation should be disconnected from the pneumatic device.
9 all kinds of accessories that are installed on the actuator shall be adjusted respectively according to the use of instructions.
10 check once a month for a year.
주소:
No. 325, Jia Hao Road, Nanxiang Industrial Park, Shanghai
사업 유형:
제조사/공장, 무역 회사
사업 범위:
공업 설비와 부품, 전기전자
경영시스템 인증:
ISO 9001
회사소개:
LIDEA·중국
봄맞이 중국의 시장이 LIDEA·의 전 세계 전략에서 LIDEA 중국을 중요한 조성이 된다면. 우수한 품질의 인 제품들이 중국 사용자들이 수용해야 합니다. 상하이 LIDEA 밸브 코아 LIDEA의 법적 허가를 받아 설립된 Ltd는 중국 시장의 거진화 및 전문 기술 지원을 제공하며, 첨단 자동 제어 밸브의 개발 및 제조에 관심을 가지고 국제 교류 및 협력을 개시합니다. 뛰어난 과학 연구 리소스인 ITselft를 통합하고 현지 중국에서 필요한 기술의 연구 및 개발을 강화함으로써 중국 시장에서 제품을 빠르게 평가하게 됩니다.
LIDEA 중국은 자동제어 밸브의 원주, 개발, 제조, 판매 및 기술 컨설팅 서비스에 대한 밸브 전문가를 크게 신조하고 확진하기 위해 최선을 다하며 중국 시장에 서비스를 제공하는 핵심 요소로 사용하고 있습니다. 아시아 및 태평양 지역의 시장에 영향을 미치는 파열기와 같은 방사성 작용력을 형성하며 시장에서 퓨터가 시장을 개발할 수 있는 강력한 힘을 제공합니다.
중국 시장에서 LDIEA가 더 높은 요구 사항을 요구하고 있습니다. 이는 매일 완성되는 것과 함께 전 세계의 중요한 시장의 결합으로, 이는 유럽 및 미국 시장의 성공적인 개발 경험인 LIDEA와 완전히 다릅니다. 중국은 LIDEA와 중국 문화를 빠르게 혼합하기 위해 현지화 일정을 중국의 전략에 도입합니다. 고급 브랜드의 문화는 이 시점에 있습니다.
혼합 문화는 서로를 더 잘 받아들이며 LIDE의 엔지니어들은 혁신적인 발전을 더욱 신속하고 효과적으로 달성할 수 있게 해 줍니다. 중국 시장의 개방에 전례 없는 속도를 남깁니다. 현재 자동 제어 밸브, 조절 밸브 등, 중요한 시리즈 내의 모든 제품이 거의 9000개 모델에서 자동 유체 제어 제품. 그 동안 당사는 유언 집행자, 제어 밸브 및 유체를 위한 중국 지역의 유관 제품, 제어 밸브 및 유체를 위한 기관 또는 중국 지역의 교환 및 협력 파트너가 되어 유럽 JAKSA와 같은 유명 브랜드의 유액 관리 제품, HEFFERSON(미국), CO-AX(독일), DynaQuip inUSA, FLO(네덜란드).
LIDEA는 집중력과 혁신 정신이 가득한 전문적인 밸브의 브랜드입니다.
세심한 작업과 정교한 작업을 통해 LIDEA의 품질을 전반적으로 향상하며, 기업 정신이 매우 만족스러운 결과를 얻으며, 모든 제품이 LIDEA의 초탁월한 기술과 기술적 수준을 보여주고, 전객적인 전략적 관점에서 밸브 브랜드를 만들고자 하는 노력을 다합니다.
업계 1위 개발 기술과 개선된 LIDEA의 마나팔링 기술은 각 사용자들로부터 좋은 평가를 받고 있습니다. LDIEA 브랜드 설립 이후, 우리는 과학과 혁신에 대해 계속 관심을 가지고 있으며, 제품 개발의 매우 진보적인 양심성을 이끌어 왔습니다. 혁신적인 학계 및 세계 유수의 브랜드 파트너와 리소스를 함께 공유하고, 세계적 수준의 우수한 상호 평가 플랫폼을 만들어 새로운 기술과 진보적인 아이디어를 갖춘 LIDEA 브랜드를 만들어 밸브 제국의 번영을 이루게 합니다.