기본 정보
Structure
Ccsb Steel Plate
Discharge Pipe Dia.
200mm
제품 설명
6 Inch Small Cutter Suction Dredger (LDCSD150)
LDCSD150 Cutter Suction Dredger of steel construction, the non self-propelled, dismountable type, is able to berth and dredge at any waters both in the coastal area and inland rivers.
The dredger can be used to excavate and transport cohesive sediment below the class III specified in code for dredging engineering construction technique issued by Ministry of Water Resources(MWR) of P.R.China.
In the course of technical designing, we have considered special requirements for local tropical climate conditions such as meteorological and waters distributing state etc.
It's hull consists of a main pontoon and two side pontoons, which is easy to dismantle or mount for transportation by road, rail or water, and is easy to reassemble at project site.The engines and dredge pump are located in the center pontoon,the two side pontoons serve as fuel bunkers,ballast tanks and storage tanks.
The dredger is powered by diesel engine. The dredge pump is driven by the engine through the gearbox. On the gearbox, two hydraulic pumps are equipped, to supply power for all the hydraulic equipment such as cutter, swing and ladder winches, and the spud rams etc.
The spacious control cabin is ergonomically designed with 360 degree view. All the operation buttons, swifts, indicators, gauges are equipped on the control desk. Only one operator can control the whole dredger in the operation room.
The dredger is painted by 4 layers of marine paint to protect from the corrosion. The ZINC anode can be used to give better anti-corrosion function.
Working Principle
A sand dredger's (CSD) suction tube has a cutter head at the suction inlet, to loosen the earth and transport it to the suction mouth. The cutter can also be used for hard surface materials like gravel or rock.The dredged sand is usually sucked up by a wear-resistant centrifugal pump and discharged through a pipe line on to the land. Sand dredger is a good choice for dredging activites.
Application
CSD series dredgers can apply to all kinds of soil structures and can be widely used in mineral digging,port(channel) dredging and reclamation works.
By absorbing advanced technology of Dutch and American related products,this series of dredgers have advantages of rational design,all hydraulic control,simple operation,little maintenance and strong power.The capacity of CSD dredgers rangs from 100m3/hr to 1000m3/hr,the dredging depth from 1m to 25m and discharge distance from 500m to 3000m which can satisfy different work demands.
After-Sales Service
1.We sign a long-time after-sale service agreement with customers.
2.We provide rational and practical design according to customers' request.
3.We send engineers to assemble and test the machine within the period as agreed in the contract.
4.Within warranty period,we provide free repair if quality problems emerge.
5.We provide free tranining of operation and maintenance for customers.
6.We supply high quality accessories in low price.
7.We make an excellent filing of customers for long-term following-up service.
No. | Description | Specification | Remark |
A | Supplier | Hebei Leader | ISO Certified Enterprise |
B | Brand | | Registered Brand |
C | Model | LDCSD-150 | |
D | Dredger Unit |
E E | 1. Dredger Type | Cutter Suction Dredger | |
| 2. Principle Dimensions | | |
(1) Length overall | 17.0 m | |
(2) Width Overall | 4.6 m | |
(3) Hull Depth | 1.4 m | |
(4) Draft | 0.8 m | |
(5) Dredging Depth | 6.0 m | |
(6) Discharge Distance | 300 m | |
(7) Suction Pipe Dia. | 250 mm | |
(8) Discharge Pipe Dia. | 200 mm | |
(9) Water Flow | 500 m3/hr | |
(10) Power | 224 Kw, Cummins | |
3. Main Pontoon | | |
(1) Length | 9.0 m | |
(2) Width | 2.2 m | |
(3) Plate Thickness | 6 mm | CCS Marine Steel Plate |
(4) Plate Thickness-Bottom | 8mm | |
4. Side Pontoons | | |
(1) Length | 11.5 m | |
(2) Width | 1.2 m | |
(3) Depth | 1.4 m | |
5. Dredging Pump | | Inside the Pontoon |
Made | SHIJIAZHUANG PUMP GROUP | Australian Warman Technology |
(2) Model | 8/6 E-G | |
(3) Head | 37 m | |
(4) Maximum Passing Particle | 120 mm | |
(5) Water Flow | 500 m3/hr | |
6. Main Engine | | |
(1) Manufacturer | Cummins | |
(2) Model | NTA855-M | |
(3) Rated Power with RPM | 224 KW @ 1800 RPM | |
(4) Amount | 1 Set | |
7. Gear Box | | |
(2) Model | Marine use | |
(3) Amount | 1 Set | |
(3) Made | Hangzhou | |
8. Cutter Head | | |
(1) Type | Crown | |
(2) Wearing type | Replaceable alloy cutter teeth | |
(3) Driven | Hydraulic Motor | |
(4) Diameter | 850 mm | |
(5) Cutter Shaft Power | 30 kw | |
(6) Speed | 0-40 r/min | |
9. Ladder Winch | | |
(1) Line Pull - Second Layer | 25 KN | |
(2) Line Speed - Second Layer | 0-20 m/min | |
(3) Wire Size | 14 mm | |
(4) Drive | Hydraulic Motor | |
10. Swing Winch | | |
(1) Line Pull - Second Layer | 25 KN | |
(2) Line Speed - Second Layer | 0-20 m/min | |
(3) Wire Size | 14 mm | |
(4) Drive | Hydraulic motor | |
11. Spuds | | |
(1) Amount | 2 | |
(2) Dia. | 277 mm | |
(3) Thickness | 14 mm | |
(4) Length | 9 m | |
(5) Material | 16 Mn | |
(6) Drive | Hydraulic Ram | |
12. Operation Cabin | | |
(1) Main Item | PLC control board | Siemens PLC |
(2) Air Condition | 1 Set | |
(3) Operation instrument, Indicator,Button | 1 Set | |
(4) Dredging Depth Indicator | 1 Set | |
13. Hydraulic System | 1 Set YUKEN series valves; Vikers Series Pumps |
14. Electric System | 1 Set Schneider Series Components |
15. Anchors and Wire Ropes | Anchors: 2 Nos. @ 100kg Side winch wire (fitting): Minimum 100 m on each side. |
16. Auxiliary enerator | |
Made | Sunvin | Supply power for charging battery, fuel pump, lights, welding machine, air conditioner,etc. |
(2) Power | 15 kw |
(3) Voltage | 220/380 |
(4) Amount | 1 Set |
17. Deck Generator | | |
Brand and Model | Changzhou Yameike | When in emergency condition, the deck generator will start to supply power. |
Power | 15 kw |
Voltage | 220/380 v |
Amount | 1 Set |
18. Light | 1 Set |
19. Signal Mast | Navigation light |
주소:
Room 601, Unit2, 1 Building, Xingguang Neighborhoods, Mingyuan Road, Gaokai District, Baoding, Hebei, China
사업 유형:
제조사/공장, 무역 회사
사업 범위:
경공업 일용품, 공업 설비와 부품, 농업 식품, 보디빌딩과 오락 여가, 야금광산물과 에너지, 의류 및 악세서리, 자동차와 오토바이와 액세서리, 제조 가공 기계, 철물, 트렁크와 가방,선물 세트
경영시스템 인증:
ISO 9001, ISO 9000, GMP, BSCI
회사소개:
허베이 산업자원부 행정부는
우리 사업의 범위를 승인했다: 허베이 리더 IMP. EXP(&E) Co., Ltd.는 Baoding HONGYE L의류 회사, Ltd.를 기반으로 설립된 전문적인 해외 무역 기업이며, 중국 상무부의 승인을 받아 자체 수입수출권을 보유하고 있으며, 주요 사업은 수입, 수출 및 IMP입니다. EXP(&E) 대행사.
현재 15개 사업부서, 1개 고객서비스부서, 1개 금융부서가 있습니다. 주요 사업부로는 기계백화점, 전자 부품, 하드웨어 및 전기 재료 부서, 컴퓨터/SoftWear 부품, 의류 및 직물 부서, 일상 생활 필수품 부서, 공예 제품 부서, 가전제품 부서, 사무용품, 교육 자료, 스포츠 및 유지 장비, 농장과 가축 제품, 광물부, 건축 자재 부서, 친환경 농정신보호 부서.
회사의 고객 서비스 부서는 포괄적인 국제 거래 운영 시스템, 통합 IMP를 구축합니다. EXP(&E) 비즈니스, 문서 작성, 상품 검사, 통관, 운송, 드로백 교환 등의 정착, 현대적인 물류 운영 플랫폼의 지원 서비스.
회사의 목표는 정직성을 위한 배려이며, 최고의 제품, 고품질의 효율적인 전문 서비스, 국내외 친구를 위한 강력한 기술 지원을 제공하는 데 최선을 다하고 있습니다.