기본 정보
Number of Switch
Double Control Switch
Structure
Power Built-in Type
Usage
Control Button, Reset Button, Control Switch
Kind
Single-pole on-off Switch
Detection Method
Retro-reflective Mode
Size
115(L)*70(W)*44(H)mm
Range
Mini 30m Line of Sight
Maximum Loads
500W, 2-Gang 400W or 3-Gang 300W Incandescent /150
Operating Temperature Range
32-104° F (0-40° C)
Use Environment
for Indoor Use Only
Z-Wave Frequency
908.42MHz
제품 설명
ZW31T In-wall Wireless Smart Switch,DimmerIntroductionThe Wall Mounted Switch is a component of the lighting control system.Wire the Wall Mounted Switch in place of a standard wall switch.Inclusion of this Switch allows remote ON/OFF control of loads connected.This Wall Mounted Switch is designed to work with otherZ-Wave enabled devices.Z-Wave nodes of other types can be added to the system and will also act as repeaters.Technical data
Operating Voltage | 120Vac/60Hz |
Maximum Load | 500W, 2-gang 400W or 3-gang 300W incandescent /150W CFL/LED |
Powered by | Z-wave 500 seires chip |
Range | Min 30m line of sight |
Relay | 15A (ON/OFF) |
Operating Temperature Range | 32-104°F (0-40°C) |
Dimensions | 115(L)*70(W)*44(H)mm |
Net weight | 130g |
Approval | Rohs,FCC, UL |
Z-wave frequency | 908.42MHz |
Installation1.Before installation ensure that the voltage supply is disconnected.IMPORTANT!Verify power is OFF to switch box before continuing.2.Remove wall plate.3.Remove the switch mounting screws.4.Carefully remove the switch from the switch box.DO NOT disconnect the wires.5.There are up to five screw terminals on the switch;These are markedA.LINE (Hot) - Black (connected to power)B.Neutral - WhiteC.LOAD - Black (connected to lighting)D.GROUND - Green/BareE.TRAVELER - Red/Other (only used in 3-way installations)Match these screw terminals to the wires connected to the existing switch.6.Disconnect the wires from the existing switch.Be careful to label wires according to thePrevious terminal connection.Observe Important Wiring InformationIMPORTANT!:This switch is rated for and intended to only be used withCopper wire.Wire Gauge RequirementsUse 14 AWG or larger wires suitable for at least 80° C for supplying Line (HOT), Load, Neutral,Ground and Traveler connections.Wire strip length:For attachment to screw terminals:Strip insulation 1" (25mm)For attachment using the enclosure's holes:Strip insulation 5/8" (16mm)UL specifies that the tightening torque for the screws is 14 Kgf-cm (12 lbf-in).7.Connect the green or bare copper ground wire to the GROUND terminal.8.Connect the black wire that goes to the fixture to the terminal marked LOAD.9.Connect the black wire that comes from the electrical service panel (Hot) to the terminalMarked LINE.10.Connect the white wire to the neutral terminal (use included jumper wire if needed).Note:The Traveler terminal is only used for 3-way or 4-way wiring and should remainInsulated if the switch is being installed in a 2-way system (one switch & one load).11.Insert Switch into the switch box being careful not to pinch or crush wires.12.Secure the switch to the box using the supplied screws.13.Mount the wall plate.14.Reapply power to the circuit at fuse box or circuit breaker and test the system.Basic OperationThe connected light can be turned ON/OFF in two ways:1.Manually from the front panel of the In-wall switch2.Remotely with a Z-Wave ControllerManual ControlThe Front Panel Toggle Switch allows the user to:Turn ON/OFF the connected fixture.To turn the connected fixture ON:Press and release up on the toggle.To turn the connected fixture OFF:Press and release down on the toggle.Adding your device to a Z-wave network:1.Follow the instructions for your Z-wave certified controller to include a device toThe Z-wave network.2.ZW31T:Quickly press ON (Up) or OFF (Down) button or three (3) times3.Once your controller has confirmed that the device has been included, refresh the Z-wave network to optimize performance.Please reference the controller's manual for instructions.Now you have complete control to turn your fixture ON/OFF or dimAccording to groups, scenes, schedules and interactive automationsProgrammed by your controller.If your Z-wave certified controller features Remote Access, you can now controlYour fixture from your mobile devices.To exclude and reset the device1.Follow the instructions for your Z-wave certified controller to exclude a device fromThe Z-wave network.2.ZW31T:Quickly press ON (Up) or OFF (Down) button or three (3) timesTo return your switch to factory defaults:ZW31T:Remove device from Gateway will restore factory mode.ZW31T:Support All On/All OffInvert SwitchIf the switch is accidentally installed upside down with "On" at thebottom and "Off" at the top, the default On/Off rocker settings canbe reversed by changing parameter 1's value to "1".? Parameter No: 1? Length: 1 Byte? Valid Values = 0 or 1 (default 0)Safety and maintenance instruction- Make sure that all electric connections and connection cables meet the pertaining regulations and are in conformity with the operating instruction.- Do not overload electrical outlets or extension cords, fire or electric shocks can be the result.- Please contact an expert in case you have any doubts about the mode of operation, the safety or connecting the appliances.- Keep all parts away from young children's reach.- Do not store this item on wet, very cold or warm places, this can damage the electronic circuit boards.- Avoid dropping or shocks, this can damage the electronic boards.- Never replace damaged power cables yourself!In such case, remove them from the net and take the devices to a workshop.- Wireless system are subject to interference from cordless phones, microwaves, and other wireless devices during installation and operation.MaintenanceThe devices are maintenance-free, so never open them.The guarantee becomes void when you open the appliance.Only clean the outside of the devices with a soft, dry cloth or a brush.Prior to cleaning, remove the devices from all voltage sources.NOTEDo not use any carboxylic cleaning agents or petrol, alcohol or similar.These will attack the surface of devices.Besides, the vapors are hazardous to your health and explosive.Do not use any sharp edged tools, screw drivers, metal brushes or similar for cleaning.Warranty 1 year
주소:
Changan Town, Dongguan, Guangdong, China
사업 유형:
제조사/공장
사업 범위:
가전제품, 경공업 일용품, 서비스, 안전과 방호, 전기전자, 제조 가공 기계, 조명, 측정 기계
경영시스템 인증:
ISO 9001
회사소개:
Nie-Tech Co., Ltd는 2009년에 설립되었으며 스마트 홈 제품의 설계, 개발 및 제조를 전문으로 하는 하이테크 제조업체입니다.
저희는 경험이 많고 혁신적인 R&D 팀을 보유하고 있으며, 가정과 산업 분야 모두에 적합한 성공적인 Z-Wave 솔루션을 다양하게 보유하고 있습니다. 우리의 광범위한 무선 기술은 고객의 신뢰성과 범위 성능에 대한 신뢰를 바탕으로 고객이 혁신적인 아이디어를 성공적인 제품으로 만들어 낼 수 있도록 도와줍니다.
ZE300 Evalogik Gateway는 스마트 홈의 신경 중심지입니다. 스마트폰을 사용하여 집에 설치된 다양한 가전 제품 및 장치에 액세스하고 제어할 수 있습니다. ZE300 Evalogik 게이트웨이는 조명, 센서, 커튼 모터, 보안 카메라 및 에너지 제어 장치에서 원격으로 제어할 수 있습니다. 가정의 Wi-Fi 네트워크로 게이트웨이를 구성하고 스마트폰에 EVALOGIK 앱을 설치하면 됩니다. 그런 다음 EVALOGIK 게이트웨이와 호환되는 모든 어플라이언스에 추가하고 연결할 수 있습니다.
"품질 우선, 고객 우선" 을 목표로 하는 QC 팀은 배송 전에 제품의 자격을 확인합니다. 저렴한 가격, 짧은 시간, 높은 품질, 그리고 우리의 엄격한 근무 태도, 이 모든 것들이 우리가 더 많은 주문을 받을 수 있도록 도와줍니다.
어쨌든, 어떤 조건에서든 비즈니스 파트너로서 당신과의 협력을 기대합니다.