기본 정보
Size
1200X2300mm 1000X2000mm
Water Absorbing Capacity
<0.1
Characteristics
Moderate Elasticity, Easy to Wash and Clean
Application
Electronics Factory, Toy Factory, Sports
사양
1000X2000MM 1200X2300MM
제품 설명
High quality TPE Balance Pad/High quality TPE Twister Stepper pad
TPE stands for Thermo Plastic Elastomer. It is a range of polymers (plastics) that can be processed (moulded or extruded) like a plastic when over their melt temperature, but exhibit properties of thermoset rubber. The advantage to using TPE over thermoset rubber, is that it can be easily re-moulded and re-worked whereas
Rubber cannot. TPE foam material is considered better for the environment because it requires less energy when
It is manufactured. TPE is also recyclable because it can be reshaped and reused for different purposes.
Environment
TPE foam is considered better for the environment because it requires less energy when it is manufactured. TPE
Is also recyclable because it can be reshaped and reused for different purposes. In general, it contains less toxic components, such as phthalates and chlorine, which are used to make PVC and other plastics. The strong odor
Of synthetic rubber is caused by chemicals that create off-gases that are released into the air. TPE foam does not have this distinctive odor.
Temperature
The creation of TPE foam was based on the need to find a resilient replacement for rubber in automobiles and other applications where there is exposure to fluctuating temperatures. TPE foams stand up to extremes in both
Hot and cold temperature without cracking.
Weight and Water
TPE foam is injected with hydrogen, which makes half as heavy by volume as neoprene. The light weight also provides environmental and financial benefits because of the savings in transporting the material. Because TPE is
A closed cell structure, it is completely waterproof. An example of an open cell structure is a rubber sponge.
Hygienic
TPE foam is used in applications as a backing to products made of fabric, such as covering and cushions for outdoor furniture. TPE foam does not absorb water, therefore the potential for mold and mildew to form is eliminated if the fabric gets wet.
Tensile Properties
Tensile properties are measurements used to describe how an elastomer performs when stretched. Several
Tests are commonly used to give an indication of how a TPE will perform in end-use environments.
Tensile at Break
This measurement is also called Ultimate Tensile. In this test, a piece of elastomer is stretched until it breaks. The amount of force needed to break the material is measured. Units are typically given in pounds per square inch (psi) or megaPascals (MPa). Elastomers with high ultimate tensile properties will be more difficult to break by stretching than an elastomer with lower values on this test.
Tear Strength
This value describes how well the elastomer resists tearing. The tear strength test essentially the same as the tensile at break test except the test bar is notched on one side to provide a propagation point. The material is stretched and the amount of force at which the test bar tears completely is recorded. Units are typically given in psi or kiloNewtons per meter (kN/m).
Tensile Modulus
In the tensile modulus test, the elastomer is stretched and resistance to the stretching is measured over a range of elongation points. This is often reported as tensile at various percentages of the original length of elastomer, such as 50, 100 and 300 percent. An elastomer might have a strong resistance to stretching initially but become weaker as it elongates (called "necking").
Elongation at Break
Elongation does not measure how hard or easy the material is to stretch, but simply how far it will stretch before it breaks. This is reported in percentage of original length. Some soft elastomers will stretch to greater than 1000 percent of their original length before breaking. A soft elastomeric TPE will typically have a much higher value
Than a hard rigid material.
주소:
No.58, Tongze Road, Tongguang Industrial Zone, Yuyao, Ningbo, Zhejiang, China
사업 유형:
제조사/공장
사업 범위:
가구, 건축과 장식재료, 공예품, 보디빌딩과 오락 여가, 서비스, 자동차와 오토바이와 액세서리, 장난감, 트렁크와 가방,선물 세트, 포장 인쇄
경영시스템 인증:
ISO 9001, ISO 14000, BREEAM, HQE, SHE Audits
회사소개:
Ningbo Mylon Rubber & Plastic Co., Ltd.는 폴리에틸렌 폼 시트, EVA 폼 시트, 전도성 EVA 폼 시트, TPE 폼 시트, EVA/PE 폼 롤, PU 폼/스폰지, NBR/PVC 폼 시트 생산에 헌신하는 전문 제조업체 및 수출업체입니다. EPDM 폼 시트, 네오프렌 폼 시트, SBR 폼 시트, EVA 고무 밑창 시트, XPE/IXPE 폼 시트, ABS 시트, PP 시트, HDPE 시트, PVC 시트, 아크릴 시트, PTFE 시트 등 폼 시트와 폼 롤 외에도 스포츠 신발, 캐주얼 신발, EVA 슬리퍼, EVA 장난감 등 다른 완제품들도 생산될 수 있습니다. 스포츠 용품, 피트니스 장비, 수상 스포츠 제품, 체조형 매트 및 포장, 가방 및 케이스, 수공예품, 건축 장식 및 해양 등의 산업에서 사용되는 제품.
친환경 방화 폼, 정전기 방지 폼, 방화 및 정전기 방지 폼, 충격 흡수 폼, 항균 폼, 고온 저항성 폼 및 오픈 셀 폼은 전자, 자동차, 운송 및 건축 장식 산업에서 널리 사용됩니다. 매달 우리는 시장에 현재 인기 있는 10개의 새로운 디자인을 제공할 수 있습니다. Mylon은 많은 해외 기업의 지정 OEM이 되었습니다. 당사의 제품은 SGS, RoHS, M1 및 UL 인증을 받았습니다.
설립 이후 지역사회의 많은 지원과 관심을 받았습니다.
저희 공장은 닝보(Ningbo) 유야오의 통구앙 산업 지구에 위치해 있으며 유명한 닝보 항구(항구)에서 80km 거리에 있습니다. 이 공장은 6,000 평방 미터의 표준 워크샵과 세계적인 수준의 장비를 갖추고 있으며, 매년 최대 30 000 큐브미터의 폼 시트와 제품을 생산할 수 있습니다. 우리는 경쟁력 있는 가격으로 고품질의 제품을 가지고 있습니다. 우리의 대용량 생산량을 바탕으로 영국, 동남아시아, 프랑스, 호주, 캐나다, 그 외 주요 고객 그룹은 중간 규모의 소매업체, 브랜드 매장, 신발 공장, 장난감 및 수공예 공장입니다.
′고품질 제품, 탁월한 서비스, 경쟁력 있는 가격 및 배송 확인′을 제공하는 EMC는 상호 이익을 바탕으로 해외 고객과 더욱 긴밀한 협력을 기대합니다. 자세한 내용은 저희에게 문의해 주십시오.