Desktop air pressure calibration table vacuum gas pressure generator device The desktop air pressure calibration platform is an important auxiliary equipment in the testing of pressure instruments. It is used in conjunction with the pressure standard to complete the calibration and testing of pressure instruments. The lever of the desktop air pressure test bench drives the piston in the large chamber to reciprocate to generate pressure or vacuum. The pressure or vacuum is output through the switch, and the pressure or vacuum is output through the regulator valve to the fine adjustment and pressure output interface. It is supplemented by delicately designed fine-tuning, fast interface, and pressure stabilizing valve. The advantages of simple operation, reasonable structure and good sealing performance can be widely used in measurement, scientific research, industrial and mining enterprises and instrument manufacturing industries. Technical indicators of desktop air pressure calibration platform 2.1 Pressure range: -0.1~600KPa -0.1~2.5KPa -0.1~10MPa, -0.1~6MPa, -0.1~4MPa, -0.1~1.6MPa, contact customer service for more ranges. 2.2 Adjust sensitivity: min 10 Pa 2.3 Dimensions: 400×300×180 (length×width×height) 2.4 Weight: 6kg 3. Operation 3.1. Positive pressure detection Press the switch in, unscrew the plugs on the output 1, output 2, and output 3 connectors, connect the standard meter and the tested meter, open the regulator valve, adjust the fine adjustment to the appropriate position (middle position), and close the air valve . For example, the pressure range is -0.095~6MPa when the operating lever is pressurized to 4~5MPa, use fine-tuning to adjust the pressure to about 6.5MPa, stabilize for 1~2 minutes, use fine-tuning to the verification point, close the pressure regulator, and check point by point. Zero point. 3.2. Negative pressure detection Pull out the switch, unscrew the plugs on the output 1 and output 2 connectors, connect the standard meter and the tested meter, open the pressure regulator valve, adjust the fine adjustment to the appropriate position (middle position), and close the empty valve. The operating lever is vacuumed when the pressure reaches about -0.095MPa. Stabilize for 1 to 2 minutes, use fine-tuning to adjust to the verification point, close the regulator valve, and detect point by point to zero. 3.3. In the high pressure state, when the pressure drops slowly, close the pressure regulator valve. (First, fine-tune the pressure to about -0.1MPa, and then slowly adjust to -0.095MPa after 1~2 minutes of stabilization) 4. Matters needing attention 4.1 The inspection table should be placed on a flat and easy-to-operate table to avoid entering the environment with highly corrosive gas and dust particles. 4.2 The inspected instrument should be properly cleaned to prevent dirt from entering the detection loop. , 4.3 The output 1 and output 2 nozzles are dedicated quick connectors, and the end faces are sealed. When installing the instrument, you don't need to use any tools to tighten it evenly. About 1 to 2 turns when the sealing surfaces are close to each other. 4.4 The output 1 and output 2 nozzles are composed of upper and lower two pieces. When using, always check whether the lower locking screw is connected reliably. If the connection is unreliable, it may cause collapse under high pressure. To 4.5 When the leverage pressure is heavy, please use the fine-tuning boost, which is easier. The desktop air pressure calibration station is an integrated pressure calibration equipment, which has the functions of pressure control fine-tuning and pressure output. It is an economical pressure measuring instrument designed by our company based on more than ten years of pressure instrument manufacturing and field application experience. In order to enable you to quickly and correctly grasp the use of this series of products, this instruction manual introduces the technical indicators of this series of products, the composition of the instrument, the use of operations, precautions, etc. in more detail. Please read the instruction manual carefully before use, in order to permanently guarantee the reliability and stability of this series of meters. FAQ 1. Are you a manufacturer or a trader? Yes, we are both. 2. What products do you have? We are focus on instruments and meters. Such as Mechanical / Optical /Power/ SafetyEnvironmental testing equipments and some hardware tools amd eletronic components. More infomation about business, please contact us we can send you catalog for reference. 3. Can i get a sample first? Yes, we are pleased to send you sample to test the quality and market. 4. Can you do OEM for us? Yes, OEM are welcome for us. Customers' brand, logo, label can be customized for the produets andcarton package, but based on a certain quantity. 5. What are your strengths? We have a complete range of products covering low, medium and high-end markets in good price in Instruments field. Fast Delivery, factory high quality and professional engineers to solve your problems.
감사를 받은 공급업체 
