비즈니스 라이센스가 검증 된 공급 업체
감사를 받은 공급업체 | 1, Part Description: | ||||||
| 1 | Independent RX and TX | |||||
| 2 | Water proof | |||||
| 3 | extension wire harness (Dia 3.0mm x 200mmL) | |||||
| 4 | 2P connect with capsule. Left for positive and right for negative with copper Pin | |||||
| 2, Electronic specification & physical character | ||||||
| Description | Standard or testing result | Item | Description | Standard or testing result | ||
| 1 | Part Number | KT40-096 | 8 | Detective angle | 30°±15° | |
| 2 | Match sensor number | KT40-T/R1212 | 9 | Intermittent space (ms) | 50 | |
| 3 | Center frequency(KHz) | 40±1KHz | 10 | Protocal | TTL | |
| 4 | Operation voltage | 5V | 11 | Connect | JST: B04B-XNISK-A-1 or custermization | |
| 5 | Operation current | 20mA | 12 | Sensor colour | Natural aluminum or customization | |
| 6 | Detective distance (Max.) | 4m | 13 | Stock temperature | -10ºC~+60ºC | |
| 7 | Blind detective distance | 4cm±1cm | 14 | Operation temperature | '+25ºC~+10ºC | |
| 3,Dimension and detective diagram | ||||||
| 4. Environmental test | ||||||
| No. | Test items | Test condition | Standard | |||
| 1 | High temp storage test | 144 hours at + 85 ºC | After the test and place in + 25 ºC (room temp) for 24 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value | |||
| 2 | Low temp storage test | 144 hours at - 40 ºC | ||||
| 3 | High temp and high humidity storage test | 144 hours at + 65 ºC and 85 ± 5% RH | ||||
| 4 | Thermal shock test | Parallel 3.9k Ω resistor at both ends of the probe, keep the temp at - 40 ± 5 ºC for 0.5h, and increase the temp to 85 ± 5 ºC within 5 minutes and keep for 0.5h.100 cycles. | After the test and place in + 25 ºC (room temp) for 24 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value | |||
| 5 | Vibration test | Products bear the vibration with frequency 10-55hz, amplitude 1.5mm,and sweep rate 1oct / min, from X, Y and Z directions for each 2 hours respectively | After the test and place in + 25 ºC (room temp) for 4 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value | |||
| 6 | Monomer drop test | 15 free fall tests carried out from 100 ± 10cm height to 50mm thick wooden floor | After the test and place in + 25 ºC (room temp) for 4 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value | |||
| 7 | Strength test of outlet | Apply 9.8N pulling force between shell and wire for 30 seconds | The wire is not loose or falling off, the product function is normal, and the wire is not damaged | |||
| 8 | Protection level | Place the probe in 15cm deep water and soak for 24 hours | Take out the capasual from the water and install it on the test board to measure the distance. The probe works normally without long sound. | |||
| 9 | High and low temp characteristic test | Keep the temp at -40ºC for 2h,increase to 25ºC and keep for 2h,increase to 85ºC and keep for 2h. | After the test and place in + 25 ºC (room temp) for 2 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value | |||
| 10 | High and low temp working test | Under high temp 85 ºC, low temp - 40 ºC, working voltage 140 Vp-p, pulse number 20, continuous working 48 hours | Probe works normally (sensitivity and residual vibration are within normal range) | |||
| 5.Test conditions and instruments | ||||||
| No. | Test item | Test instruments/method | Test condition | |||
| 1 | resonant frequency | Impedance analyzer | ambient temperature 25 ± 5 ºC | |||
| 2 | static capacitance | LCR bridge measuring instrument | ambient temperature 25 ± 5 ºC | |||
| 3 | residual oscillation | KT test equipment | ambient temperature 25 ± 5 ºC | |||
| 4 | sensitivity | KT test equipment | 0.8m at room temperature, target Φ 75mm PVC pipe | |||
| 5 | Angle (X & Y axis) | KT test board, as per Fig.1 | Under normal room temperature, the probe is 500mm from the ground, 500mm from the object to be detected, and the object to be detected is Φ 75mm PVC pipe, 1000mm high. The test environment: 2 meters in front and 1.5m in the left and right without obstacles | |||
| 6 | Maximum allowable input voltage | KT test board and Oscilloscope | 140vp-p, pulse width 0.5ms, | |||
| intermittent: 10ms | ||||||
| 7 | Mean time between failures | aging test rack | Test temp 25±5ºC | |||
| 6.Precautions | ||||||
| 1. Please confirm with us which industry will be used before purchasing for selection. | ||||||
| 2. In order to prevent the sensor from failure, working failure or performance degradation, the anti failure function shall be added to the product design, and the product shall not be used under the following or similar conditions. (a) strong shock or vibration (b) prolonged exposure to high temperature and humidity; (c)In corrosive gas or sea breeze (d)Exposure to dissolved organic matter (e)Dusty environment; (f)Over allowable input voltage | ||||||
| 7.Quality assurance | ||||||
| The sensor defects due to the manufacturer during the warranty period of the product can be replaced free of charge. | ||||||
| The following situations are not covered by the warranty. | ||||||
| 1, improper use or handling by users. | ||||||
| 2, changed or repaired by the users. | ||||||
| 3,any other situation that does not belong to the responsibility of the manufacturer, such as natural disasters, accidents, etc. | ||||||
비즈니스 라이센스가 검증 된 공급 업체
감사를 받은 공급업체 
