고확장율 친수성 수영장 물 팽창 고무 물막이

• 커스터마이징: 사용 가능
• 판매 후 서비스: 3년
• 애플리케이션: 실내, 야외, 지하, 콘크리트 공동 워터 스탑, 방수
• 모델 번호.: PZ2010
• 자격증: CE, ISO, ISO9001
• 모양: 굴러요
• 입력합니다: 솔리드 코어 밀봉 스트립
• 단면 모양: 직사각형
• 성능: 고압
• 저속화: 지속적인 음란
• 표준: 표준, 비표준
• 재질: 고무
• 사용: 설명을 참조하십시오
• 사용자 지정: 네
• 색상: 블랙/레드
• 볼륨 확장: 150%-400%
• 경도: 30-90개의 해안
• 샘플: 무료 샘플
• 프로젝트 솔루션 기능: 그래픽 디자인, 3D 모델 디자인, 완벽한 솔루션
• 주요 자료: 고무
• 표면 처리: 돌출
• 운송 패키지: 팔레트가 있는 상자
• 규격: 20 * 30, 10 * 10, 10x20, 20 * 25 또는 요구 사항
• 원산지: Jiangsu, China
• 세관코드: 4016931000
• 생산 능력: 일주일에 50000미터

제품 설명

High performance hydrophilic waterstops for sealing construction joints 

For sealing construction joints and penetrations in concrete structures. Waterstop is a strip applied hydrophilic rubber swelling waterstop for use in all kinds of cast-in-place concrete construction joints, as well as steel, concrete and thick-walled PVC (minimum 1/8") pipe penetrations. When exposed to water, the rubber expands, creating a compression seal within the joint or pipe penetration, blocking the passage of water.

제품 설명

FEATURES & BENEFITS

Advantages
Easy to use
Rapid expansion
Dimensionally stable, even at high temperatures
Reproducable swell after wet/dry cycling
Suitable for fresh and salt water
Contains no bentonite
Typical Applications
Vertical and horizontal cast-in-place concrete joints where limited or no movement is expected.
Around through-wall pipe penetrations.
Ideal for new concrete structures or between new and existing concrete.

Benefits:
Easy to use
Rapid expansion
Dimensionally stable, even at high temperatures
Reproducable swell after wet/dry cycling
Suitable for fresh and salt water
Contains no bentonite

사양

No	Test item		UNIT	Requirement	Inspection	Result
1	External quality		/	Each meter of water-expandable rubber surface is allowed to have a depth of not more than 2mm,an area of not more than 16mm2 dents,bubbles,impurities,scars and other defects not more than 4.	There are no dents,bubbles,impurities,scars and other defects on the surface.	Pass
2	Width		mm	29.0~31.5	29.9	Pass
3	Thickness		mm	19.0~21.5	19.8	Pass
4	Hardness-Shore A		Shore A	45±10	37	Pass
5	Tensile strength		Mpa	≥3*80%	4	Pass
6	Elongation at break		%	≥350*80%	614	Pass
7	Volume expansion ratio		%	≥400	479(method 1)	Pass
8	Repeated water immersion test	Tensile strength (Mpa)	Mpa	≥2x80%	3.4	Pass
9		Elongation at break % (minimum)	%	≥250x80%	368	Pass
10		Volume expansion ratio % (minimum)	%	≥300	459(method 1)	Pass
11	Low temperature bending(-20°Cx2h)		/	not cracked	not cracked	Pass

RECOMMENDED USES

Use Swelling Waterstop to permanently waterproof horizontal or vertical construction joints, pipe penetrations, between precastelements and other concrete joints. Not for use at expansion joints. Suitable for use in sewage and containment structures. May be used inareas with chloride or sulfate contaminated soils and in contact with sea water.

INSTALLATION NOTES
Easy to install where conventional waterstops would require complex fitting.
Fix in position using adhesive or masonry nails at regular intervals.
A suitable adhesive should be used to fix the seal to metal or PVC pipe surfaces.
On irregular surfaces ensure that direct contact is made between the seal and the substrate along the entire section.
The seal can be exposed to wet site conditions for up to 3 days prior to the placing of concrete, provided it has been coated with an inhibitor to protect it.
A minimum of 70mm of concrete is required on all sides to encapsulate the seal within the concrete.
Joints can be secured by welding, glueing or overlapping.
Swelling is slower in cold conditions and faster in hot.
Typically 28 days to reach full swell in Standard Swell Waterstop.

APPLICATION

Before using this product, refer to Application Instruction.
Basic Application Procedure: Using Adhesive, or other approved fastening device, adhere  Swelling Waterstop at or near thecenter of the construction joint to clean dry concrete surface. For added long-term protection of the outboard reinforcing steel, apply Waterstop Treatment to the concrete surface first and adhere to the treatment when it is dry. Strip-ends should be tightly butted andnot overlapped. Avoid rain or immersion in water as this may cause premature swelling. If premature swelling occurs, dry the sufficiently to restore its original dimensions and ensure material is properly affixed to the surface before pouring concrete.

회사 프로필

Suzhou ARISONS New Material Co.,Ltd.

ARISONS is a professional Rubber&Construction manufacturer in China. The factory is located in Jiangsu, closed to Shanghai. After 15 years of development, it has a mature production system, a professional engineering team, a quality inspection department and a strong production line, providing a one-stop design scheme and product design for customers in many countries.

Our main products are rubber sealing products, pipe sealing ring, car sealing ring, etc., water treatment equipment, aeration pipe, aeration disk, large pipe machine, driving, etc., we pay attention to quality, and will make different solutions according to different customers, provide the cheapest price, achieve the most perfect effect, has reached more partners for customers, look forward to cooperation with you!

FAQ

Q1. What is your terms of packing?
A: Generally, we pack our goods in Blank Cartons. We privode carton LOGO print service after getting your authorization letters.

Q2. What is your terms of payment?
A: T/T 30% as deposit, and 70% before after receive the copy of B/L. We'll show you the photos of the products and packages before you pay the balance.

Q3. What is your terms of delivery?
A: We accept FOB,CIF,CNF,DDP,DDU,LC.etc

Q4. How about your delivery time?
A: Generally, it will take 7 to 10 days after receiving your advance payment. The specific delivery time depends on the items and the quantity of your order.

Q5. Can you produce according to the samples?
A: Yes, we can produce by your samples or technical drawings.

Q6. What is your sample policy?
A: We can supply the sample for free, client only need to pay the delivery cost.