기본 정보
제품 설명
Descriptions
R&B bearings will support you to spot the difference in the example of HF 101612 and FC 10 as follows:
1: HF is flat end needle roller; while FC is pointed end needle roller;
2: HF is light series, while FC is heavy duty series one way bearing. It means FC will have higher torque rating than HF, which is the most important factor for one way bearing.
3: There is only one needle roller in each cage window for HF one way bearing; while multi-roller in each cage window for FC one way bearing.
4: Single roller per stainless steel spring for HF one way bearing; while multi-roller per stainless steel spring for FC one way bearing.
one-way needle roller bearing
HFL series drawn cup one-way needle roller bearing has two supporting needle bearing and one roller clutch which shares a punching outer ring, and can be used as a special space-saving support. The two supporting bearing are assembled on both sides of the roller clutch, and endure the radial load. The supporting needle bearing is composed of plastic cage and needles.
Main features: the unidirectional movement, reverse lock; the high conversion frequency and high conversion accuracy.
SPECIAL NOTES
? HFL series has two integral radial bearings arranged on both sides of needle roller clutch. They can therefore support radial forces in particularly space-saving bearing arrangements.
? Plastic springs (HFL...KF) are available for some sizes.
? Partially knurled outer ring (HFL...R) is available upon request.
? A special tool is suggested when assembling the clutch and bearing assembly. For details please contact our engineers.
? Only after the clutch and bearing assembly has been pressed into the hole of the housing, the drawn thin-walled outer ring could then obtain its final dimension and geometric accuracy.
? The transmissible torque and the stresses which can be taken by the housing are subject to the material and the wall thickness of the housing, and such data is needed upon enquiry.
? The clutch and bearing assembly can be normally used in temperature range from -30°C to 120°C. For the working environment above 70°C, oil lubrication is recommended.
Specification:
Fw=inner diameter D=outer diameter C=height
Shaft Diameter | Clutch Designation | Mass Approx | Borndary Dimensions | Torgue Ma | 1 Limiting Speed | Suitable Drawn Cup Bearings |
Plastic Springs | Steel Springs | Fw | D | C | Rotating Shaft Min-1 | Rotatng Outer Ring Min-1 |
mm | g | mm | Nm | rpm |
HF ( INA/ ) |
3 | HF0306KF | | 0.9 | 3 | 6.5 | 6 | 0.2 | 36000 | 7000 | HK0306TN |
4 | HF0406KF | -- | 1 | 4 | 8 | 6 | 0.34 | 34000 | 8000 | HK0408TN |
HF0406KFR | -- | 1 | 4 | 8 | 6 | 0.1 | 34000 | 8000 | HK0408TN |
6 | HF0608KF | | 2.8 | 6 | 10 | 8 | 1.5 | 20000 | 11000 | HK0608 |
HF0612KF | HF0612 | 3 | 6 | 10 | 12 | 1.76 | 23000 | 13000 | HK0608 |
HF0612KFR | HF0612R | 3 | 6 | 10 | 12 | 1.76 | 23000 | 13000 | HK0608 |
| HF061210 | 3.5 | 6 | 12 | 10 | 3 | 20000 | 13000 | HK061208 |
8 | HF0812KF | HF0812 | 3.5 | 8 | 12 | 12 | 3.15 | 17000 | 12000 | HK0808 |
HF0812KFR | HF0812R | 3.5 | 8 | 12 | 12 | 4 | 17000 | 12000 | HK0808 |
-- | HF061210 | 3.2 | 8 | 12 | 10 | 3 | 16000 | 12000 | HK0808 |
-- | HF081410 | 3.6 | 8 | 14 | 10 | 4.6 | 15000 | 11000 | HK081410 |
-- | HF081610 | 4.1 | 8 | 16 | 10 | 5.5 | 15000 | 11000 | HK081610 |
-- | HF081412 | 4 | 8 | 14 | 12 | 5 | 16000 | 12000 | HK081410 |
10 | HF1012KF | HF1012 | 4 | 10 | 14 | 12 | 5.3 | 14000 | 11000 | HK1010 |
HF1012KFR | HF1012R | 4 | 10 | 14 | 12 | 1.5 | 14000 | 11000 | HK1010 |
12 | -- | HF1216 | 11 | 12 | 18 | 16 | 12.2 | 11000 | 8000 | HK1212 |
14 | -- | HF1416 | 13 | 14 | 20 | 16 | 17.3 | 9500 | 8000 | HK1412 |
16 | -- | HF1616 | 14 | 16 | 22 | 16 | 20.5 | 8500 | 7500 | HK1612 |
18 | -- | HF1816 | 16 | 18 | 24 | 16 | 24.1 | 7500 | 7500 | HK1812 |
20 | -- | HF2016 | 17 | 20 | 26 | 16 | 28.5 | 7000 | 6500 | HK2010 |
| | HF2216 | 25 | 22 | 28 | 16 | 32 | 6500 | 6000 | |
25 | -- | HF2520 | 30 | 25 | 32 | 20 | 66 | 5500 | 5500 | HK2512 |
| | HF273420 | 30 | 27 | 34 | 20 | 110 | | | |
| | HF404725 | 45 | 40 | 47 | 25 | 185 | | | |
| | HF485620 | 43 | 48 | 56 | 20 | 230 | | | |
| | HF586820 | 86 | 58 | 68 | 20 | 320 | | | |
30 | -- | HF3020 | 36 | 30 | 37 | 20 | 90 | 4500 | 4500 | HK3012 |
35 | -- | HF3520 | 40 | 35 | 42 | 20 | 121 | 3900 | 3900 | HK3512 |
Shaft Diameter | Clutch Designation | Mass Approx | Borndary Dimensions | Torgue Ma | 1 Limiting Speed | Suitable Drawn Cup Bearings | Plastic Springs | Steel Springs | Fw | D | C | Rotating Shaft Min-1 | Rotatng Outer Ring Min-1 | mm | g | mm | Nm | rpm | HF ( INA/ ) | 3 | HF0306KF | | 0.9 | 3 | 6.5 | 6 | 0.2 | 36000 | 7000 | HK0306TN | 4 | HF0406KF | -- | 1 | 4 | 8 | 6 | 0.34 | 34000 | 8000 | HK0408TN | HF0406KFR | -- | 1 | 4 | 8 | 6 | 0.1 | 34000 | 8000 | HK0408TN | 6 | HF0608KF | | 2.8 | 6 | 10 | 8 | 1.5 | 20000 | 11000 | HK0608 | HF0612KF | HF0612 | 3 | 6 | 10 | 12 | 1.76 | 23000 | 13000 | HK0608 | HF0612KFR | HF0612R | 3 | 6 | 10 | 12 | 1.76 | 23000 | 13000 | HK0608 | | HF061210 | 3.5 | 6 | 12 | 10 | 3 | 20000 | 13000 | HK061208 | 8 | HF0812KF | HF0812 | 3.5 | 8 | 12 | 12 | 3.15 | 17000 | 12000 | HK0808 | HF0812KFR | HF0812R | 3.5 | 8 | 12 | 12 | 4 | 17000 | 12000 | HK0808 | -- | HF061210 | 3.2 | 8 | 12 | 10 | 3 | 16000 | 12000 | HK0808 | -- | HF081410 | 3.6 | 8 | 14 | 10 | 4.6 | 15000 | 11000 | HK081410 | -- | HF081610 | 4.1 | 8 | 16 | 10 | 5.5 | 15000 | 11000 | HK081610 | -- | HF081412 | 4 | 8 | 14 | 12 | 5 | 16000 | 12000 | HK081410 | 10 | HF1012KF | HF1012 | 4 | 10 | 14 | 12 | 5.3 | 14000 | 11000 | HK1010 | HF1012KFR | HF1012R | 4 | 10 | 14 | 12 | 1.5 | 14000 | 11000 | HK1010 | 12 | -- | HF1216 | 11 | 12 | 18 | 16 | 12.2 | 11000 | 8000 | HK1212 | 14 | -- | HF1416 | 13 | 14 | 20 | 16 | 17.3 | 9500 | 8000 | HK1412 | 16 | -- | HF1616 | 14 | 16 | 22 | 16 | 20.5 | 8500 | 7500 | HK1612 | 18 | -- | HF1816 | 16 | 18 | 24 | 16 | 24.1 | 7500 | 7500 | HK1812 | 20 | -- | HF2016 | 17 | 20 | 26 | 16 | 28.5 | 7000 | 6500 | HK2010 | | | HF2216 | 25 | 22 | 28 | 16 | 32 | 6500 | 6000 | | 25 | -- | HF2520 | 30 | 25 | 32 | 20 | 66 | 5500 | 5500 | HK2512 | | | HF273420 | 30 | 27 | 34 | 20 | 110 | | | | | | HF404725 | 45 | 40 | 47 | 25 | 185 | | | | | | HF485620 | 43 | 48 | 56 | 20 | 230 | | | | | | HF586820 | 86 | 58 | 68 | 20 | 320 | | | | 30 | -- | HF3020 | 36 | 30 | 37 | 20 | 90 | 4500 | 4500 | HK3012 | 35 | -- | HF3520 | 40 | 35 | 42 | 20 | 121 | 3900 | 3900 | HK3512 |
1:;KF,KF; 2:R;
Shaft Diameter | Clutch Designation | Mass Approx | Borndary Dimensions | Torgue Ma | 1 Limiting Speed | Basic Load Ratings | Plastic Springs | Steel Springs | Fw | D | C | Rotating Shaft Min-1 | Rotatng Outer Ring Min-1 | C | Co | KN | mm | g | mm | Nm | rpm | HFL ( INA/ ) | 3 | HFL0308 | -- | 3 | 3 | 3.6 | 8 | 1 | -- | -- | -- | -- | 4 | HFL0408 | -- | 3.5 | 4 | 8 | 8 | 1.5 | -- | -- | -- | -- | 6 | HFL0615KF | HFK0615 | 4 | 6 | 10 | 15 | 1.76 | 23000 | 13000 | -- | -- | HFL0615KFR | HFL0615R | 4 | 6 | 10 | 15 | 0.5 | 23000 | 13000 | -- | -- | -- | HFL061012K | 5 | 6 | 10 | 12 | -- | 21000 | 12000 | -- | -- | 8 | -- | HFL081212K | 6 | 8 | 12 | 12 | -- | 20000 | 12000 | -- | -- | -- | HFL081412K | 7 | 8 | 14 | 12 | -- | 19000 | 12000 | -- | -- | HFL0822KF | HFL0822 | 7 | 8 | 12 | 22 | 3.15 | 17000 | 12000 | 4.05 | 4.15 | HFL0822KFR | HFL0822R | 7 | 8 | 12 | 22 | 1 | 17000 | 12000 | -- | -- | 10 | HFL1022KF | HFL1022 | 8 | 10 | 14 | 22 | 5.3 | 14000 | 11000 | 4.3 | 4.65 | HFL1022KFR | HFL1022R | 8 | 10 | 14 | 22 | 1.5 | 14000 | 11000 | -- | -- | 12 | -- | HFL1226 | 18 | 12 | 18 | 26 | 12.2 | 11000 | 8000 | 6.3 | 6.5 | 14 | -- | HFL1426 | 20 | 14 | 20 | 26 | 17.3 | 9500 | 8000 | 7.1 | 7.7 | 16 | -- | HFL1626 | 22 | 16 | 22 | 26 | 20.5 | 8500 | 7500 | 7.7 | 9 | 18 | -- | HFL1826 | 25 | 18 | 24 | 26 | 24.1 | 7500 | 7500 | 8.3 | 10.3 | 20 | -- | HFL2026 | 27 | 20 | 26 | 26 | 28.5 | 7000 | 6500 | 8.9 | 11.5 | 25 | -- | HFL2530 | 44 | 25 | 32 | 30 | 66 | 5500 | 5500 | 10.9 | 14.1 | 30 | -- | HFL3030 | 51 | 30 | 37 | 30 | 90 | 4500 | 4500 | 12.6 | 17.6 | 35 | -- | HFL3530 | 58 | 35 | 42 | 30 | 121 | 3900 | 3900 | 13 | 19.3 |
| | | Fw | D | C | | Torrington/ & NSK/ | FC4K | 1 | 4 | 8 | 6 | 0.34 | FC6 | 3 | 6 | 10 | 12 | 1.76 | FC6K | 3 | 6 | 10 | 12 | 1.76 | FC8 | 4 | 8 | 14 | 12 | 5.3 | FCL8K | 3.5 | 8 | 12 | 12 | 5 | FC10 | 4.8 | 10 | 16 | 12 | 6 | FCL10K | 4 | 10 | 14 | 12 | 5.3 | FC12 | 11 | 12 | 18 | 16 | 12.2 | FC14K | 13 | 14 | 20 | 16 | 17.3 | FC16 | 14 | 16 | 22 | 16 | 20.5 | FC20 | 17 | 20 | 26 | 16 | 28.5 | FC25 | 30 | 25 | 32 | 20 | 66 | FC30 | 36 | 30 | 37 | 20 | 90 | FC35 | 40 | 35 | 42 | 20 | 121 | FCB8 | 10 | 14 | 14 | 20 | 5 | FCB10 | 15 | 16 | 16 | 20 | 10 | FCB12 | 18 | 18 | 18 | 26 | 12.2 | FCB16 | 22 | 22 | 22 | 26 | 20.5 | FCB20 | 27 | 26 | 26 | 26 | 28.5 | FCB25 | 44 | 32 | 32 | 30 | 66 | FCB30 | 51 | 37 | 37 | 30 | 90 | FCB35 | 58 | 42 | 42 | 30 | 121 |
| | | Fw | D | C | | Torrington/ & NSK/ | RC02 | 2 | 3.175 | 7.15 | 6.35 | 1.5 | RC040708 | 3.5 | 6.35 | 11.112 | 12.7 | 1.9 | RC040708-FS | 3.5 | 6.35 | 11.112 | 12.7 | 1.9 | RC061008 | 4.7 | 9.525 | 15.875 | 12.7 | 4.83 | RC061008-FC | 4.7 | 9.525 | 15.875 | 12.7 | 4.83 | RC081208 | 9.2 | 12.7 | 19.05 | 12.7 | 7.9 | RC081208-FS | 9.2 | 12.7 | 19.05 | 12.7 | 7.9 | RC101410 | 14.5 | 15.875 | 22.225 | 15.88 | 15.4 | RC101410-FC | 14.5 | 15.875 | 22.225 | 15.88 | 15.4 | RC121610 | 17 | 19.05 | 25.4 | 15.88 | 20.9 | RC121610-FS | 17 | 19.05 | 25.4 | 15.88 | 20.9 | RC162110 | 16.2 | 25.4 | 33.338 | 15.88 | 45 | RC162110-FC | 16.2 | 25.4 | 33.338 | 15.88 | 45 | RCB061014 | 12 | 9.525 | 15.875 | 22.22 | 4.83 | RCB061014-FS | 12 | 9.525 | 15.875 | 22.22 | 4.83 | RCB081214 | 16 | 12.7 | 19.05 | 22.22 | 7.9 | RCB081214-FC | 16 | 12.7 | 19.05 | 22.22 | 7.9 | RCB101416 | 21.3 | 15.875 | 22.225 | 25.4 | 15.4 | RCB101416-FS | 21.3 | 15.875 | 22.225 | 25.4 | 15.4 | RCB121616 | 26.5 | 19.05 | 25.4 | 25.4 | 20.9 | RCB121616-FC | 26.5 | 19.05 | 25.4 | 25.4 | 20.9 | RCB162117 | 44.8 | 25.4 | 33.338 | 26.99 | 45 | RCB162117-FS | 44.8 | 25.4 | 33.338 | 26.99 | 45 |
shaft dia. d | boundary dimensions | torque capacity | Fw | D1 | D2 | B | A | mm | mm | N.m (.) | Kg.cm(.) | 4 | 4 | 8 | 8.4 | 6 | 2.6 | 0.08 | 0.82 | 4 | 8 | 8.4 | 6 | 2.6 | 0.15 | 1.53 | 6 | 6 | 10 | 10.4 | 8 | 2.8 | 0.25 | 2.55 | 6 | 10 | 10.4 | 8 | 2.8 | 0.44 | 4.49 | 6 | 10 | 10.4 | 8 | 2.8 | 0.44 | 4.49 | 6 | 10 | 10.4 | 12 | 2.8 | 0.88 | 8.98 | 8 | 8 | 12 | 12.4 | 9 | 2.6 | 0.49 | 5 | <, ;, TD align=middle> 8 | 12 | 12.4 | 9 | 2.6 | 0.88 | 8.98 | 8 | 14.2 | 15 | 12 | 3.6 | 1.18 | 12.04 | 8 | 14.2 | 15 | 12 | 3.6 | 1.96 | 20 | 8 | 14.2 | 15 | 12 | 3.6 | 1.96 | 20 | 8 | 14.2 | 15 | 14.5 | 3.6 | 2.65 | 27.04 | 10 | 10 | 16 | 17 | 10 | 5 | 1.18 | 12.04 | 10 | 16 | 17 | 10 | 5 | 1.96 | 20 | 10 | 16 | 17 | 12 | 5 | 1.37 | 13.98 | 10 | 16 | 17 | 12 | 5 | 2.35 | 23.98 | 10 | 16 | 17 | 12 | 5 | 2.35 | 23.98 | 12 | 12 | 18 | 19 | 16 | 5.1 | 6.28 | 64.08 |
(1).nA. (2),. ,-0mm~-0.25mm,. |
Parameter list of OWC needle roller bearing
Shaft Dia. | Model | Weight | Size(mm) | Driving Torque |
mm | g | Inner Dia. | Outer Dia. | Height | ( Nm ) |
4 | OWC 410 | 1.8 | 4 | 10 | 5.4 | 2.8 |
5 | OWC 511 | 2 | 5 | 11 | 5.4 | 3.5 |
6 | OWC 612 | 2.3 | 6 | 12 | 5.4 | 5.2 |
8 | OWC 814 | 2.8 | 8 | 14 | 5.4 | 6.1 |
10 | OWC 1016 | 3 | 10 | 16 | 5.4 | 9.5 |
4 | OWC 406 | 1.6 | 4 | 8 | 6 | 2.5 |
4 | OWC 408 | 1.8 | 4 | 8 | 8 | 3.1 |
6 | OWC 612-8.4 | 2.35 | 6 | 12 | 8.4 | 6.8 |
6 | OWC 61407 | 2.1 | 6 | 14 | 7 | 6.6 |
6 | OWC 720 | 2.5 | 6 | 12.7 | 7.5 | 7.3 |
6 | OWC 087 | 2.38 | 6 | 10.2 | 8 | 4.6 |
6 | OWC 178 | 3 | 6 | 10.2 | 15 | 7.3 |
8 | OWC 81607 | 2.6 | 8 | 16 | 7 | 7.5 |
8 | OWC 812 | 3 | 8 | 12.7 | 7.3 | 6.8 |
8 | OWC 816-5.5 | 3.5 | 8 | 16 | 5.5 | 8.2 |
8 | OWC 816-6.2 | 3.8 | 8 | 16 | 6.2 | 8.8 |
10 | OWC 1008 | 3.35 | 10 | 16 | 8 | 9.7 |
10 | OWC 1019 | 8.5 | 10 | 19 | 11 | 19.8 |
17 | OWC 173512 | 22.5 | 17 | 35 | 12 | 78 |
17 | OWC 173516 | 25.5 | 17 | 35 | 16 | 95 |
17 | OWC 203316 | 23 | 20 | 33 | 16 | 108 |
MARKS:NON-STANDARD CAN BE PRODUCED |
Transfer capability:
Under the conditions of using the recommended mounting tolerances, the maximum torque that can be transmitteddepends primarily on the design of the seat shell and the shaft (materials, strength, wall thickness). Only when thewall thickness of the seat shell and its material allowable stress certain requirements, the clutch can transfermoment Md.
Installation:
Should be used the assembly mandrel with Needle roller bearings, needle roller clutch pressure holing hole(installed). When the clutch side of the direction of the arrow relative to the shaft is rotated, the clutch will lock, andtherefore should be noted locking direction before installation.
Lubrication:
HF-drawn cup needle roller clutch in oil and grease lubrication. Lubricated with oil, however, before you can get thebest performance, the standard HF-Drawn Cup Clutch has been filled with lithium grease.
Performance test:
The technical requirements of the test method and the standard circle described with Needle roller bearingsdimensional inspection mandrel used nominal size to take the tolerance zone as the lower limit for the h5 shaftalong the arrow in the opposite direction in the clutch can be locked.
Mounting tolerances:
The technical requirements of the seat shell HF-Needle roller bearings, the axis of the tolerance zone h5, the surfaceroughness Ra0.2m, not less than the hardness of HRC60.
Operating temperature:
HF-drawn cup needle roller clutch lubrication properly can the temperature range of -30 ° C to +120 °C long-running,short-term up to 150 ° C Operating Temperature. Lithium Grease Run
ONE WAY BEARING APPLICATIONS
Paper moving for copiers, fax machines, paper towel dispensers, etc.
Exercise equipment
Appliances
Two-speed gearboxes
Rack indexing drives
Converters, non-return devices and transcendental clutches.
Fishing Reels, RC Cars, RC Helis, RC Engines
INSPECTION OF ONE WAY BEARINGS
Although the outer cup of the clutch is accurately drawn from strip steel, it can go slightly out of round during heat treat. When the assembly is pressed into a ring gage or properly prepared housing of correct size and wall thickness, it becomes round and properly sized. Direct measurement of the outside diameter of a drawn cup assembly is an incorrect procedure. The proper inspection procedure is as follows:
1. Press the assembly into a ring gage of the proper size as given in the tabular data.
2. Gage the bore with the specified plug gages of the proper size, as given in the tables of dimensions.
- The locking plug is rotated to insure lockup when the clutch is operated at low limit shaft and is mounted in a high limit housing strong enough to properly size the clutch.
- The overrun plug is rotated to ensure free over-running when the clutch is operated on a high limit shaft and is mounted in a low limit housing.
- The go plug and no go plug insure proper size of the bearings in the clutch and bearing assemblies.
주소:
Changhong West Road 182, Wujin District, Changzhou, Jiangsu, China
사업 유형:
제조사/공장
사업 범위:
공업 설비와 부품, 야금광산물과 에너지, 자동차와 오토바이와 액세서리, 제조 가공 기계, 철물
경영시스템 인증:
ISO 9001
회사소개:
Changzhou Lisongtai Industrial Motion Technology Co., Ltd는 원웨이 클러치, 오버러닝 클러치, 니들 롤러 베어링과 같은 다양한 원웨이 베어링을 생산하는 데 특화된 제조업체입니다. 1,000가지 이상의 미터법 및 인치 시리즈 니들 베어링 지정을 한 방향으로 착각하는 2000개 이상의 표준 모델은 국내외 시장에서 오토바이, 전기 및 공기 구동식 공구, 프린터, 경공업, 기계, 건설기계, 자동차 트럭, 사무실 장비에 정기적으로 제조되고 널리 사용됩니다. 또한, 다양한 작업에 대한 고객의 요구 사항에 따라 특수 베어링도 제공됩니다. 우리는 한국, 이란, 터키, 불가리아, 루마니아, 러시아, 이탈리아, 노르웨이, 미국, 캐나다, 우리는
무엇입니까?
우리 공장은 경제개발 해안 도시-산업지구-우진 창저우 시(Jiangsu)에 있었습니다. 교통이 편리해서, 기차를 타고 상하이까지 1시간 정도 걸립니다.
주요 제품은 무엇입니까?
원웨이 베어링, 원웨이 클러치, 오버러닝 클러치, 백스톱, 캠 클러치, 니들 롤러 베어링, 지지 롤러 및 커브 베어링, 원통형 롤러 베어링 매트가 있는 스러스트 볼 베어링 우리는 많은 주식을 보유하고 있으며 비표준 제품, 고객의 도면 또는 샘플을 생산할 수 있는 주의 대상이 됩니다.
우리의 장점은 무엇입니까?
제품: 1999년, 엔지니어로서 우리의 상사는 큰 베어링 공장에서 일하면서 원웨이 클러치 베어링을 개발 및 설계하기 시작했습니다. 지금까지 BB 시리즈, MZ 시리즈, TFS 시리즈, NSS 시리즈 RSBW 시리즈 개발에 성공했는데, 이는 Janpan의 TSUBAKI 브랜드와 비교했을 때 높은 품질로 도달했음을 확인할 수 있습니다.
Stieber 클러치, GMN 클러치, Ringspann 클러치, Formsprag 클러치, NSK 클러치와 동등한 Quliaty ECT
GFR 시리즈, DC 시리즈, ASNU 시리즈, NFR 시리즈, GFK 시리즈, NF 시리즈, AE 시리즈, AA 시리즈 등, 고품질 도달 거리를 확인할 수 있는 것은 독일의 STIEBER 브랜드와 비교할 수 있습니다.
FE 시리즈, FP 시리즈, FND 시리즈, FKN 시리즈 원웨이 클러치 베어링은 독일 GMN 브랜드와 비교했을 때 높은 품질 수준에 도달했음을 확인할 수 있습니다.
고객에게 업계 최고의 서비스를 지속적으로 제공하기 위해 베어링 공급 및 설계의 최전선에 서서 새로운 베어링으로 개발을 계속하고자 하는 우리의 의도는 바로 이 때문입니다.
공장 장비: 이 회사는 가장 진보된 CNC 자동 생산 라인, 자동 조립 라인 및 다양한 테스트 장비를 보유하고 있습니다. 저희가 제조한 베어링은 모두 저소음, 저진동, 저마찰, 고정밀, 높은 밀봉, 높은 회전 속도 및 긴 수명
Quantity Control: 2011 ISO9001:2008 품질 관리 시스템 인증을 획득했고, 모든 제품은 여러 번 검사하기 전에 발송됩니다. 또한 필요한 경우 상세 도면과 서비스를 제공합니다.
응용 프로그램이 무엇입니까?
기계, 리듀서, 호이스트, 엘리베이터, 자동차, 가전제품, 직물기계, 인쇄기계, 식품기계, 광산 기계 등
우리 제품이 판매된 곳은?
전 세계 우리의 제품은
독일, 영국, 네덜란드, 스페인, 이탈리아,
인도, 인도네시아, 필리핀, 태국,
이란,
멕시코의 두바이,
미국의
"품질 및 서비스"는 우리가 실제로 실천한 당신의 주요 관심사가 되어야 합니다. 우리의 제품 카테고리를 찾아보고 귀하의 문의사항을 알려주십시오. 우리의 목표는 고객에게 양질의 서비스를 제공하고 경쟁력 있는 가격을 제공하는 것입니다. 적절한 공급, 큰 재고, 편리한 교통편을 갖춘 우리는 새로운 고객이 우리를 방문해서 따뜻하게 환영한다.