기본 정보
Detection Range
30~100meter;
Detection Angle
180deg+/-90(Horizontal); 20deg+/-10deg(Vertical)
Operating Temp
-25oc~55oc
Dimensions
171(L)*50(W)*77(H)mm
Frequency
868.42MHz/908.42MHz/919.82MHz/921.42MHz
제품 설명
ZW113 Z-wave Two Beams active Infrared sensor Technical data Installation Introduction This sensor is a Z-Wave enabled device (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave enabled network. Technical data *Detection range: 30~100meter;*Detection angle: 180°±90°(horizontal); 20°±10°(vertical)*Power supply: 12VDC*Range: 30m line of sight*Operating temp: -25°--+55°(ºC)*Quiescent current: 18(uA)*Alarm current: 100(uA)*Dimensions: 171(L)*50(W)*77(H)mm*Frequency: 868.42MHz/865.2MHz/869.0MHz/908.42MHz/921.42MHz Installation 1. Release cover tab to open the cover. 2. Install ZW113 to the relate position, avoid obstacles such as trees, insure the set-base is stable, and avoid sunshine/lamplight directly shining. 3. Close the cover back to sensor. 4. For "Add" in (adding to): Put the Z-Wave Interface Controller into "Add" mode, and following its instruction to add the ZW113 to your controller. To get in the "Add" mode, the distance between sensor and controller is suggested to be in one meter. Press the learn switch of ZW113 once. The LED on the ZW113 should stop flashing, if not, please try again. For "Remove" from (removing from) a network: Put the Z-Wave Interface Controller into "Remove" mode, and following its instruction to delete the ZW113 to your controller. Press the learn switch of ZW113 once to be excluded. The LED on the ZW113 should start to flash. For "Group": removing the cover of the ZW113 to get into "Awake" mode, then put the Z-Wave Interface Controller into "Group", and following its instruction to associate the ZW113 with other device. Close the cover back after "Group" done, afterward the ZW113 will get into "Sleep" mode for power saving. Support one association group (5 nodes). Note: "Awake" mode: it is to leave the "Sleep" mode by removing the cover of ZW113, to allow the Z-Wave Interface Controller to do "Group. 5. Using gum wall plug & screws to mount ZW113 at 2 meters above surface. To enhance proper operation, place ZW113 on the angle which can detect the room widely. The solid area means the detector's coverage range. Safety and maintenance instruction- Make sure that all electric connections and connection cables meet the pertaining regulations and are in conformity with the operating instruction.- Do not overload electrical outlets or extension cords, fire or electric shocks can be the result.- Please contact an expert in case you have any doubts about the mode of operation, the safety or connecting the appliances.- Keep all parts away from young children's reach.- Do not store this item on wet, very cold or warm places, this can damage the electronic circuit boards.- Avoid dropping or shocks, this can damage the electronic boards.- Never replace damaged power cables yourself! In such case, remove them from the net and take the devices to a workshop.- Wireless system are subject to interference from cordless phones, microwaves, and other wireless devices during installation and operation. MaintenanceThe devices are maintenance-free, so never open them. The guarantee becomes void when you open the appliance. Only clean the outside of the devices with a soft, dry cloth or a brush. Prior to cleaning, remove the devices from all voltage sources. NOTEDo not use any carboxylic cleaning agents or petrol, alcohol or similar. These will attack the surface of devices. Besides, the vapors are hazardous to your health and explosive. Do not use any sharp edged tools, screw drivers, metal brushes or similar for cleaning. Warranty 1 year
주소:
Dongguan, Guangdong, China
사업 유형:
제조사/공장
사업 범위:
가전제품, 경공업 일용품, 서비스, 안전과 방호, 전기전자, 제조 가공 기계, 조명, 측정 기계
경영시스템 인증:
ISO 9001
회사소개:
Nie-Tech Co., Ltd는 2009년에 설립되었으며 스마트 홈 제품의 설계, 개발 및 제조를 전문으로 하는 하이테크 제조업체입니다.
저희는 경험이 많고 혁신적인 R&D 팀을 보유하고 있으며, 가정과 산업 분야 모두에 적합한 성공적인 Z-Wave 솔루션을 다양하게 보유하고 있습니다. 우리의 광범위한 무선 기술은 고객의 신뢰성과 범위 성능에 대한 신뢰를 바탕으로 고객이 혁신적인 아이디어를 성공적인 제품으로 만들어 낼 수 있도록 도와줍니다.
ZE300 Evalogik Gateway는 스마트 홈의 신경 중심지입니다. 스마트폰을 사용하여 집에 설치된 다양한 가전 제품 및 장치에 액세스하고 제어할 수 있습니다. ZE300 Evalogik 게이트웨이는 조명, 센서, 커튼 모터, 보안 카메라 및 에너지 제어 장치에서 원격으로 제어할 수 있습니다. 가정의 Wi-Fi 네트워크로 게이트웨이를 구성하고 스마트폰에 EVALOGIK 앱을 설치하면 됩니다. 그런 다음 EVALOGIK 게이트웨이와 호환되는 모든 어플라이언스에 추가하고 연결할 수 있습니다.
"품질 우선, 고객 우선" 을 목표로 하는 QC 팀은 배송 전에 제품의 자격을 확인합니다. 저렴한 가격, 짧은 시간, 높은 품질, 그리고 우리의 엄격한 근무 태도, 이 모든 것들이 우리가 더 많은 주문을 받을 수 있도록 도와줍니다.
어쨌든, 어떤 조건에서든 비즈니스 파트너로서 당신과의 협력을 기대합니다.